Rolling Mill Bearing Designation Cross Reference Guide
A rolling mill bearing designation cross reference lets you match an SKF, NSK, Koyo, NTN or Timken part number to the right four-row tapered or cylindrical roller bearing without guessing dimensions. Most general-purpose bearings follow ISO size conventions, but rolling mill, slewing and inch tapered families use manufacturer-specific numbering that hides bore, outer diameter and width inside the code. This guide decodes each major system so you can identify, quote and replace mill bearings with confidence.
Rolling mill bearings endure extreme radial loads, shock, contamination and heat, so a misread suffix can mean the wrong cage, seal or internal clearance — and a costly line stoppage. Below we break down the numbering logic brand by brand, then show how to confirm a match before ordering.
Why Rolling Mill Bearing Designations Diverge from ISO
ISO 15 establishes boundary dimensions for general radial bearings, which is why a 6208 deep groove ball bearing is a 6208 everywhere. Rolling mill bearings, however, are application-engineered: four-row tapered and cylindrical roller bearings are built to mill housing envelopes, not to a universal catalogue. Each maker encodes bore, outside diameter, width, cage type and sealing in its own prefix and suffix scheme.
That is why a cross reference is essential. You cannot assume an SKF 313812 equals any NSK number by pattern; you must translate the code back to dimensions and features. The sections below give you the decoding rules for the most common mill bearing families.
Four-Row Tapered Roller Bearings: Brand-by-Brand Decoding
Four-row tapered roller bearings carry the heaviest combined loads in roll necks and backup roll positions. Their designations vary widely, so learn each maker's logic separately.
SKF Four-Row Tapered Bearings
SKF uses a structured numeric system for four-row tapered bearings, typically starting with a series prefix followed by bore and dimension codes. Because the full logic is proprietary and sample-dependent, always confirm against the SKF rolling mill catalogue before ordering. The key practical point: SKF mill numbers rarely reveal bore at a glance, so dimension verification is mandatory.
NSK Four-Row Tapered Bearings (KV, KVE, KVS)
NSK's system is the most transparent of the major brands. The first three digits usually indicate bore in millimetres, and later digits encode outside diameter.
- 100KV1701 — 100 = 100 mm bore; the 170 block indicates 170 mm outside diameter. If the digits after KV are fewer than four, outside diameter cannot be read directly.
- 440KVE5901E — 440 = 440 mm bore; the 590 block indicates 590 mm outside diameter.
- STF450KVS5901 — digits 4–6 give 450 mm bore; digits 10–12 give 590 mm outside diameter.
NSK offers KV, KVE and KVS structures. KVE and KVS are sealed designs built for long service life and reduced grease consumption — a major advantage in mills where relubrication access is limited.
Koyo (JTEKT) Four-Row Tapered Bearings
Koyo uses distinct prefixes for standard, special and sealed four-row tapered bearings.
- Standard: 47T131010 — 47T = four-row tapered; digits 4–5 give bore 65 mm (13 × 5). For bore above 500 mm, Koyo switches to 4TR plus the bore number, e.g. 4TR500B.
- Standard (alternate): 37276 and 47376 — first two digits = four-row tapered; third digit = width series; digits 4–5 give 380 mm bore (76 × 5).
- Special structure: 45D724535 — 45D = special four-row tapered; digits 4–5 give 360 mm bore (72 × 5); digits 6–7 give 450 mm outside diameter (45 × 10); digits 8–9 give 350 mm width (35 × 10).
- Sealed structure: 47TS563829 — 47TS = sealed four-row tapered; digits 5–6 give 280 mm bore (56 × 5); digits 7–8 give 380 mm outside diameter (38 × 10); digits 9–10 give 290 mm width (29 × 10).
NTN Four-Row Tapered Bearings
NTN keeps it simpler: open four-row tapered bearings use 6259XX, 6230XX, 6231XX and CRO series. Sealed versions add an LL suffix, e.g. CRO…LL. The CRO family is widely used in mill stands where sealed-for-life performance is preferred.
Timken Four-Row Tapered Bearings
Timken designations like M 252349D /10/10C D split into three components: inner assembly, single outer ring and double outer ring. The prefix letters (1–2 characters) and the first digit encode angle and series information, digits 2–4 give the basic series, and digits 5–6 identify the component. Because Timken inch and metric mill bearings are often custom-matched, always order the complete assembly reference.
Four-Row Cylindrical Roller Bearings: Cross Reference
Four-row cylindrical roller bearings dominate roll neck positions because they handle high radial loads at speed. Their designations are equally brand-specific.
SKF Four-Row Cylindrical Bearings
SKF numbers are typically six digits beginning with 31 — for example 313812 or 314553. Bore cannot be read from the number; you must consult the SKF catalogue or measure the bearing.
NSK Four-Row Cylindrical Bearings
NSK uses the RV pattern: 180RV2601 means 180 mm bore and 260 mm outside diameter (26 × 10). The logic mirrors the KV tapered system.
Koyo Four-Row Cylindrical Bearings
Koyo uses FC: 32FC23180 gives 160 mm bore (32 × 5), 230 mm outside diameter (23 × 10) and 180 mm width. The FC prefix signals four-row cylindrical construction.
NTN Four-Row Cylindrical Bearings
NTN's 4R prefix marks four-row cylindrical: 4R2035 indicates 100 mm bore (20 × 5).
Timken Four-Row Cylindrical Bearings
Timken uses RY and RX structures: 280RY1783 is a 280 mm bore RY (brass cage) bearing, while 300RX1846 is a 300 mm bore RX (pin-type steel cage) bearing. The letter pair tells you the cage and internal design.
Ancillary Mill Bearings: Deep Groove, Angular Contact and Thrust
Beyond the four-row families, rolling mills use deep groove ball, angular contact and thrust bearings, mostly following SKF numbering. You may not read dimensions from these codes, but the prefix tells you the category:
- 306xxx — mill deep groove ball bearings, e.g. 306841. Browse our deep groove ball bearings range for comparable general-purpose sizes.
- 305xxx — angular contact ball bearings, e.g. 305262D. See angular contact ball bearings for combined-load applications.
- 35xxxx — double-direction thrust roller bearings, e.g. 351019C. Our axial cylindrical roller bearings cover heavy thrust duties.
- Bore + TFV/TFX — screwdown and pressure bearings, e.g. 800TFX01 or 149TFV01.
These ancillary bearings are usually low-volume, so confirm the exact code against the mill builder's drawing when replacing them.
How to Cross-Reference a Rolling Mill Bearing Safely
Use this checklist before you commit to a substitute:
- Measure the envelope. Record bore, outside diameter and overall width in millimetres, plus corner radii if accessible.
- Decode the original code. Apply the brand rules above to extract dimensions and features (seal, cage, clearance).
- Match features, not just size. A sealed KVE and an open KV share dimensions but differ in lubrication strategy and life.
- Check load and speed ratings. Confirm the substitute meets the mill stand's radial and axial load demands at operating speed.
- Verify cage and internal clearance. Mill bearings often run C3 or C4 clearance; substituting C2 will cause overheating.
For related inch tapered sizes used in mill auxiliary equipment, our roller bearings collection includes tapered and cylindrical options, while cylindrical roller bearings cover high-radial-load positions. If your mill uses inch tapered cups and cones, models such as 02474-02420 tapered roller bearings show how inch designations map to metric dimensions.
Practical Tips from the Workshop Floor
Experienced mill maintenance teams keep a cross-reference sheet taped inside the roll shop cabinet. Three habits prevent most ordering errors:
- Photograph the bearing stamping before removal — codes fade with grease and heat.
- Record the mill stand number alongside the bearing code, because the same stand may use different bearings on drive and operator sides.
- Keep a sealed versus open note; upgrading an open position to a sealed KVE or 47TS design can extend relubrication intervals significantly.
Where a mill uses oil seals or transmission components alongside bearings, matching the seal lip material to the bearing's lubrication method matters as much as the bearing code itself. Explore our oil seals and seals ranges to complete the assembly.
Frequently Asked Questions
What does the KV code mean in an NSK rolling mill bearing?
KV denotes NSK's four-row tapered roller bearing structure. KVE and KVS are sealed variants designed for longer life and lower grease consumption. The digits before KV give bore in millimetres, and the block after KV indicates outside diameter.
Can I replace an SKF 313812 with an NSK or Koyo equivalent?
Only after confirming dimensions and features. SKF 31-series numbers do not reveal bore, so measure the bearing envelope and match bore, outside diameter, width, cage and clearance against the NSK RV or Koyo FC equivalent before substituting.
How do I read a Koyo 47T bearing number?
47T signals a four-row tapered bearing. Digits 4–5 give bore: 47T131010 means 13 × 5 = 65 mm bore. For bore above 500 mm, Koyo uses 4TR plus the bore number, such as 4TR500B.
What is the difference between Timken RY and RX four-row cylindrical bearings?
RY indicates a brass cage design, while RX indicates a pin-type steel cage. Both are four-row cylindrical roller bearings; the cage choice affects load capacity, lubrication and speed suitability.
Why can't I read dimensions from SKF mill bearing numbers?
SKF encodes mill bearing dimensions in proprietary series numbers rather than exposing bore and outside diameter directly. You must consult the SKF rolling mill catalogue or measure the bearing to confirm size.
Need a Rolling Mill Bearing Cross Reference? Talk to OiBearing
Send us the original bearing code, a photo of the stamping and your measured bore, outside diameter and width. Our team will cross-reference SKF, NSK, Koyo, NTN and Timken rolling mill bearings and quote a matched replacement with the correct cage, seal and clearance. Email [email protected] with your mill stand details and we will respond with availability and lead time.